Gate Parts & Welding in McKinney - Made to Measure, Written Price

Trusted Gate Parts & Welding for McKinney Homeowners

Gate parts and welding in McKinney typically costs between $95 and $600, depending on whether you need a hinge replaced, a post re-set, or a cracked rail welded and reinforced. Most hinge, latch, and roller replacements can be completed in a single visit, and we stock common parts on our trucks so we’re not driving back and forth across Collin County while your gate hangs crooked. Call (430) 226-4507 and a live person picks up, any hour, any day.

Call (430) 226-4507

Ironworks Gate Co. has welded and rebuilt gates in McKinney for over 42 years, since 1984. Victor Salinas, our founder, still walks job sites and checks welds personally before a technician loads the truck. We’ve repaired everything from a rusted horse pasture gate in Lucas to a 500-pound iron driveway gate in Stonebridge Ranch that had pulled its post clean out of the ground. When we fix a gate, we fix it once. Then we hand you a written 90-Day Done Right Promise so there’s nothing to argue about later.

Key takeaways:

• Hinge, roller, and latch replacements in McKinney typically run $95 to $350 including parts and labor
• Most welding and parts jobs are completed in one visit; we carry common parts and our own welding rig
• Upfront pricing, settled before any work starts. No surprises on the bill, ever
• Written 90-Day Done Right Promise on every job, no paperwork, no arguing
• A live person answers (430) 226-4507 around the clock, every day of the week

What Our Gate Parts & Welding Service Includes

Gates fail in predictable ways. Hinges wear egg-shaped and bind. Posts rot or lean. Rails crack at the welds. Rollers flatten on one side. Latches stop catching. Each failure is specific, and each has a specific fix that lasts. Here is exactly what we do under every sub-service, and when McKinney homeowners should call us for McKinney Gate Parts & Welding.

Hinge Replacement

A sagging gate is almost always a hinge problem before it’s a gate problem. When the barrel of the hinge wears, the gate drops and drags on the latch side, which then stresses the post, the latch, and the operator motor. We remove the old hinge, grind the surface clean, and weld or bolt a properly sized hinge in place, usually the same day. If the gate has hung for years on one worn hinge, we check the others and replace what’s needed so you’re not calling back in six months.

Post Replacement

In McKinney’s clay-heavy soil, posts heave in wet winters and settle in dry summers, which slowly pulls a gate out of square. A leaning post is not just cosmetic; it changes the gate’s geometry and wears every other component unevenly. We dig out the old post and any rotted wood or crumbling concrete, set a new square post in proper concrete or welded steel footing, and re-hang the gate so it swings clean. Victor Salinas has re-set hundreds of posts across Collin County and knows which depth and footing works for this soil.

Rail Repair

Rails crack most often at the welds, where the frame flexes with every open and close cycle. A cracked rail lets the pickets carry weight they were never meant to carry, and the crack spreads quickly. We grind the crack back to clean steel, weld it with proper penetration, and often add a gusset or reinforcement plate so the repair outlasts the original weld. If the rail is too far gone, we replace that section entirely, matching the metal and profile of the existing gate.

Custom Welding

Sometimes the part a gate needs does not exist on a shelf. Wrought-iron scrollwork snapped in a storm, or a custom estate gate needs a matching section added where a new panel was installed. Our welders fabricate what’s missing from raw steel, match the existing patina and texture, and paint or powder-coat to blend. Because we are a welding company first, not a parts-swapping outfit, we can rebuild a gate element from scratch when that is the right fix, which is why we offer the Best Gate Parts & Welding in McKinney, TX.

Gate Rollers

Sliding gates ride on rollers, and rollers are wear items. When a roller bearing fails, the gate drags, grinds, and eventually stops moving, often mid-open, which strains the motor and the rack. We replace worn rollers with the correct diameter and bearing type for your track, clean and lubricate the rail, and check the entire run so the gate rolls like it did the day it was installed. For heavy steel or iron sliding gates in McKinney’s larger properties, we use sealed bearings that hold up to our heat and wet spring seasons.

Latch & Lock

A latch that won’t catch is more than an annoyance; it’s an open driveway at night. We replace mechanical latches, install magnetic and solenoid locks for automated gates, and set latching hardware so it engages fully every cycle. We also repair and align striker plates, which often wear from years of the same misalignment. If your latch barely caught four years ago, it won’t catch at all in a hard north Texas wind, so we fix the alignment, not just the part.

Brands We Service for Gate Parts & Welding

We maintain and weld repair the full range of gate hardware and automation brands found in McKinney driveways, and our techs open their parts bins with confidence because they know what’s on the gate. For example, on LiftMaster automated gates, we regularly replace the pull-to-open and push-to-open hardware, from cycle-tested hinges to the bracket welds at the opener arm. Our techs understand LiftMaster’s torque and limit-switch demands, which means the weld we make holds up to the force the motor applies every single cycle.

Mighty Mule gates are popular on smaller driveways and acreage lots around McKinney, Prosper, and Anna, and we’ve repaired hundreds of them. The hardware Mighty Mule ships with the unit is often under-spec for heavy gates, so we weld heavier brackets and replace the factory hinges with bearings that carry the weight. On FAAC and BFT systems, the common failures are cracked weld points at the articulated arm and worn pivot hardware at the hinge, both of which we replace and weld properly on the first visit. Whether you have one of these brands, a Ghost Controls unit, or any other make on the driveway, we carry or fabricate the part it needs.

Signs You Need Gate Parts & Welding Right Now

• The gate sags and scrapes the ground on the latch side. Hinges have worn past their tolerance, and every day you push through a dragging gate, you’re putting extra load on the post and the operator. It will not fix itself, and the longer it drags, the more parts it damages.
• You can see a crack anywhere in the metal frame, at a weld, or near a hinge point. Cracks in steel or iron propagate with each open-close cycle. What’s a hairline crack today is a snapped rail in a storm next month. A cracked frame can also drop a gate off its hinges, and a falling gate is not a risk anyone should take.
• The post is leaning, or you can wobble it by hand. A loose post means the gate’s full weight is levered into a foundation that is no longer holding. In McKinney’s expansive clay, this gets worse every season. We re-set posts before the gate pulls the post over completely and takes the opener wiring with it.
• The gate groans, screeches, or shudders when it moves. Rollers and hinges should operate quietly; noise means metal is wearing against metal without the protection it needs. The longer it runs dry, the more parts you replace later. A quick parts-and-lubrication visit is cheaper than a full rebuild.
• The latch no longer catches or the gate pops open. A failed latch leaves your driveway open to whoever or whatever wanders by. It also lets the gate swing in the wind, which slams the opener and can crack welds at the frame corners. We consider a non-latching gate an urgent safety issue and we’ll make it right promptly.

Safety note: Gate frames, heavy steel panels, and garage-style tensioned springs can carry hundreds of pounds of stored energy. A cracked weld releasing suddenly, or a hinge failing while you’re under the gate, causes serious injury every year. We strongly recommend you never attempt to weld or replace load-bearing gate hardware yourself. Let a trained professional with the right rig, the right PPE, and 42 years of experience handle it.

Our Gate Parts & Welding Process - Step by Step

We follow the same deliberate process on a $95 latch replacement as we do on a $600 post re-set and custom weld. Four decades of doing this work right has taught us that the process is the product.

1. 1
   You call, a live person answers, we schedule the visit. We do not have a voicemail tree. You will speak to someone at Ironworks Gate Co. who knows gates and can ask smart questions about what you’re seeing, any hour, any day. We schedule a window and we show up in that window.
2. 2
   We inspect the gate, the posts, the hinges, the weld points, and the operator. Our technician checks the entire gate, not just the symptom you called about. With over four decades in this trade, we spot additional wear that would fail months from now. We show you what we found and explain what needs attention now versus what can wait.
3. 3
   We agree on a written, upfront price. The price is settled before we unload a single tool. No work happens on a surprise invoice. The quote covers parts, materials, and labor, and the number on the quote is the number on the bill. We build in the 90-Day Done Right Promise and any standing offers, like $50 off a repair over $250, so you know exactly what the job costs.
4. 4
   We do the work right, in one visit when we can. Our trucks carry common hinges, rollers, latches, brackets, and a mobile welding rig. That means most jobs get done the day we arrive, not half-done pending a parts order. If a custom fabricated piece is required, we tell you precisely when it will be ready and we keep that date.
5. 5
   We test the gate through its full cycle, then hand you the written promise. Every gate we repair is cycled multiple times, loaded, and checked for alignment, weld integrity, and clean operation. Then we give you the written 90-Day Done Right Promise, no paperwork, no fine print, no arguing. If it’s not right, we come back and make it right.

How Much Does Gate Parts & Welding Cost in McKinney?

Gate Parts & Welding Near McKinney - Our Service Area

Ironworks Gate Co. serves McKinney and the surrounding Collin County communities, including Prosper, Anna, Celina, Melissa, Princeton, Fairview, Allen, Murphy, Little Elm, Lucas, and Frisco. Most McKinney repairs can be scheduled within a couple of days, and emergency calls from homeowners with a gate that won’t latch or won’t open are prioritized whenever possible. If you’re in a neighboring community, reach out; we make the drive and we bring the truck fully stocked.

Back to the home page for the full list of gate services we provide.

Frequently Asked Questions - Gate Parts & Welding in McKinney

Schedule Your Gate Parts & Welding Service in McKinney Today

Call (430) 226-4507 for a free, no-obligation estimate on any gate parts or welding job in McKinney. A live person answers around the clock, every day. We’ll give you a straight price before we start, and we’ll stand behind the work with a written 90-Day Done Right Promise. Done right, and backed in writing.

Written by Victor Salinas, Owner at Ironworks Gate Co., serving McKinney since 1984.