Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Frisco
Gate parts and welding in Frisco usually means one of three things: a hinge post has shifted in the black clay, a weld has cracked at the top rail, or a storm has left a gate sagging and out of alignment. In most Frisco neighborhoods, a hinge replacement or post reset runs $280-$650, and a custom welding repair typically falls between $180 and $520. We’re Ironworks Gate Co., and we work on gates in Frisco every week. If your gate isn’t opening or closing right, call us at (430) 226-4507 and a live person will answer.
Why Ironworks Gate Co. Is Frisco’s Preferred Gate Parts & Welding Company
Frisco’s gate stock has a very particular character. Most of the homes here went up between 2000 and 2020, built by a small group of production builders who installed ornamental iron and powder-coated aluminum driveway gates in nearly identical configurations. That means the same failure modes show up in clusters across entire subdivisions. We know those patterns well enough to diagnose a problem over the phone before we send a truck.
Victor Salinas has run our shop with a simple rule: a gate has to close like the day it was hung. That applies whether it’s a hand-built iron gate in Starwood or a builder-grade aluminum gate in a newer section of 75034. Our technicians arrive in uniform, background-checked, and we quote a firm price before any work begins. Every completed job is backed by our written 90-Day Done Right Promise.
Frisco homeowners tell us the same things: they want the gate fixed once, they want it to match the original spec, and they don’t want to fight with an HOA committee afterward. We get it. And we plan to be taking those calls in Frisco for another forty years.
Our Gate Parts & Welding Services in Frisco
Hinge Replacement
Hinges are the most common point of failure on Frisco gates, especially on the heavier ornamental iron swing gates found in Stonebriar and Starwood. A worn hinge lets the gate sag a quarter inch, which throws off the latch and puts extra load on the operator motor. We replace hinges in place, match the original mounting pattern, and touch up any exposed metal so the repair doesn’t look like a patch job. Most hinge replacements on a standard Frisco driveway gate run $280-$450.
Post Replacement
North Texas black clay heaves. A gate post set in a shallow footing will shift seasonally, pull out of plumb, and eventually stress every weld at the hinge point. We saw this recently in Stonebriar after spring rains, where a hinge post had shifted enough to throw the gate a full inch out of alignment. Our team cut out the old footing, poured a deeper footing with rebar, and re-welded the hinge post plumb before remounting the operator bracket. A full post replacement with correct footing depth in Frisco soil typically runs $450-$850.
Rail Repair
High winds from spring storm fronts flex solid infill gates and crack welds where the pickets meet the top rail. Over time those cracks grow, the gate loses rigidity, and the operator starts fighting a gate that wants to flex instead of swing. We cut out the cracked weld, prep the joint, and re-weld to original spec. On aluminum gates, we use a spool gun and matching wire, then touch up the powder coat. Rail repairs generally run $180-$400 depending on how many welds need attention.
Custom Welding
Some Frisco gates were built by small local shops, and replacement parts aren’t sitting on a shelf. We do custom fabrication for missing pickets, broken finials, and one-off hardware in our own welding shop. If a builder part is available, we order it to spec; if it isn’t, we make it. Custom welding work in Frisco starts around $180 and goes up based on materials and shop time. We’ll give you a written number before we pick up a torch.
For a full rundown of what we offer, see our Gate Parts & Welding services page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Frisco
We stock parts and service the operator brands most common on Frisco driveways: LiftMaster, FAAC, and Mighty Mule are the three we see most often in 75033, 75034, and 75035. Our technicians are trained on all of them, and we carry common replacement brackets, control boards, and photocells on our trucks so most jobs finish in a single visit. If your operator is struggling after a storm surge, we’ll diagnose the board and wiring as part of the same call.
Common Gate Parts & Welding Problems We See in Frisco Homes
- Sagging gates after heavy rain: Expansive clay swells, shifts the hinge post, and the gate starts dragging or the latch misses the striker. The real fix is resetting the post in a deeper footing, not shimming the hinge and hoping.
- Cracked welds at the top rail: Spring storm winds flex solid infill gates repeatedly, and the welds at the picket-to-rail joints fatigue. We cut the old weld, clean the joint, and re-weld with matching material.
- Operator boards damaged by surges: Lightning strikes and power surges during thunderstorms take out control boards and low-voltage wiring to safety photocells. We replace the damaged board and test the whole low-voltage side before declaring the job done.
- HOA compliance issues: A repair that uses the wrong picket profile or a mismatched powder-coat color gets flagged by the architectural committee and you pay for it twice. We cross-reference the original builder spec before ordering.
Getting Your Gate Secured After a Storm
When a storm has knocked out power to your Frisco home, most gate operators have a manual release lever that lets you push the gate open by hand. On LiftMaster and FAAC models, the release is typically a small handle or knob on the operator arm or chain rail. Pull the release, push the gate slowly, and don’t force it against wind. If the gate feels heavy or binds, stop and call us. A gate that fights you is a warning that a hinge or post has already failed. After the storm passes, we can inspect the welds, reset any shifted posts, and get the operator running again. Power surges in Frisco thunderstorms are a known killer of operator boards. If your gate won’t respond after the power comes back, call (430) 226-4507 and we’ll send a tech out.
Pricing for Gate Parts & Welding in Frisco, TX
Gate work in Frisco runs a little higher than in older North Texas towns because of the HOA compliance factor and the need to match builder specs. Here’s what we see in the current Frisco market:
- Hinge replacement: $280-$450, depending on gate weight and hinge count
- Post replacement with new concrete footing: $450-$850
- Rail repair or re-welding: $180-$400
- Custom fabrication of a picket or finial: $180-$520
- Operator bracket replacement: $150-$300
More complex jobs, like resetting two posts and re-welding a full gate frame, can climb to $1,200 or more. The price is always quoted and agreed before any work starts, in writing, with no surprises on the bill. We offer a free estimate on every job, so you’ll know the exact number before you commit. Current standing offers include $50 off any repair over $250 and $89 for a seasonal tune-up.
We Also Serve Cities Near Frisco
Our Frisco crews also run calls to Prosper, Little Elm, Plano, and Celina. If you’re in one of those towns and your gate is sagging or a weld has cracked, the same written pricing and 90-Day Done Right Promise applies. Call (430) 226-4507 and we’ll get you on the schedule.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Frisco
Pull the manual release lever on the operator arm, push the gate slowly, and stop if it binds or feels heavy. Most Frisco operators have a clearly marked release handle, but if you can’t find yours or the gate won’t move, call us. We can talk you through it on the phone, and our Frisco techs can be there the same day if the gate won’t secure or close. Every call is answered by a live person, 24/7.
Yes, we match original builder specifications exactly. That means picket profile, powder-coat color, finial style, and hardware finish. We photograph the existing gate, cross-reference the original builder sheet when it’s available, and order replacements to match. Starwood and Stonebriar both enforce strict architectural review, and we’ve done this work long enough to know what the committees check. Call (430) 226-4507 and we’ll start with photos and measurements.
The real fix is resetting the hinge post in a deeper concrete footing with rebar. North Texas black clay swells when wet and shrinks in drought, and shallow footings get pushed around. Shimming hinges or cranking the operator limit switch buys a few weeks. A proper post reset in Frisco runs $450-$850 and gives you a plumb post that won’t move with the seasons.
Yes. We use a spool gun with the right aluminum wire, weld the picket from the back side where possible, and touch up the welded area with color-matched powder-coat paint. The surrounding finish isn’t burned or stripped. We do this on Frisco gates every month, including the espresso bronze and matte black finishes common in 75034.
Test the gate with an obstruction: start the gate closing, then block the beam with your hand. If the gate doesn’t reverse within two seconds, the photocell or its wiring is compromised. After a lightning strike, the cell body may look fine while the board inside is fried. We check the whole low-voltage side, replace damaged photocells and wiring, and retest. The cost usually falls between $120 and $250 for a full photocell and wiring replacement in Frisco.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Frisco homeowners with gate parts, welding, and repair.