FAAC Gate Motor & Opener Nationwide

FAAC Gate Motor & Opener in McKinney: What to Know First

FAAC gate motor and opener repair in McKinney typically runs $240 to $680 depending on whether we’re replacing a control board, a capacitor, or the motor itself, and most jobs are done in a single visit. We’re an independent FAAC service provider, not a factory shop, which means we can use OEM or quality aftermarket parts whichever makes more sense for your gate. If your FAAC opener is dead, slow, or slamming, call (430) 226-4507 and a live person will pick up.

Call (430) 226-4507

This page is for McKinney homeowners who have a FAAC swing or slide gate motor acting up, or who are pricing out a replacement before the old one quits entirely. Victor Salinas and the Ironworks Gate Co. team have been working on FAAC equipment across Collin County for decades, and we know which models hold up and which ones need a specific fix at a specific age.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. The brand shows up on a lot of McKinney estate gates because the motors are quiet and the 24V systems are safe to work around. But every line has its patterns, and we’ve seen most of them more than once.

• FAAC 400 and 402 swing operators losing travel limits. These older electromechanical units rely on limit switches that wear out or drift over time. The gate starts stopping six inches short, or it overtravels and the hinge groans. We pull the cover, verify the switch state, and reset or replace the limits so the gate lands exactly where it should every cycle.
• FAAC 750 and 760 slide motor thermal trips in Texas heat. McKinney summers push a slide operator harder than the factory ever expected. The thermal overload on a 750 will cut out mid-cycle on a 104-degree afternoon, then mysteriously work again at dusk. The fix is checking current draw under load and often replacing a tired capacitor or a dragging wheel that’s making the motor work twice as hard.
• FAAC control board faults from power flickers. The E024 and 455D control boards are reliable until a lightning storm or a utility blink sends a surge through the line. Symptoms look like a dead board: no response from the remote, no LED, nothing. Sometimes it’s just a blown fuse on the board. We test before we quote a board replacement, and we’ve saved McKinney customers hundreds by finding the five-dollar fuse first.
• FAAC photocell and safety-edge misalignment. A FAAC opener that reverses for no reason usually has a photocell that’s drifted or a safety edge with a dead spot. The gate will close halfway, think it hit something, and reopen. We clean the lenses, realign the beam, and ohm-test the edge so the gate closes the first time, every time.
• FAAC hydraulic operators losing pressure after years of service. Some McKinney homes still run older FAAC hydraulic swing operators. When a seal starts weeping, the gate moves sluggish or drifts after it stops. That’s a seal and fluid job, not a whole new motor. We reseal, refill with the correct fluid spec, and the gate runs like it did when the house was new.

Our FAAC Gate Motor & Opener Process

Every FAAC job follows the same path, whether it’s a no-open on a 400 or a full slide-motor swap on a 750. Here’s how it goes.

1. 1
   You call, a person answers. We take down what the gate is doing, what model opener is on it, and what time works. No voicemail trees, no callbacks at 9 a.m. the next day.
2. 2
   We diagnose on site. Our tech pulls the cover, checks voltage, and actually watches the gate run a cycle. We don’t guess from the symptoms over the phone and we don’t sell parts until we’ve confirmed the failure.
3. 3
   You get a fixed price before any work starts. We tell you exactly what’s wrong, what the parts cost, and what the labor will be. That number is agreed to before a single bolt is turned. If it changes, it changes with your signature, not after the fact.
4. 4
   We fix it with the right part. For FAAC, we carry common OEM boards, capacitors, and limit components on the truck. When aftermarket makes more sense on an older unit, we’ll tell you why and what the tradeoff is. No surprises either way.
5. 5
   We test it like we own it. Five full open-close cycles, safety edge and photocell verified, force settings matched to the gate’s weight. We run it until it’s boring.
6. 6
   We stand behind it in writing. Every repair leaves with our 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Motor & Opener Costs in McKinney

Honest numbers, based on what we actually bill in McKinney and the surrounding neighborhoods like Stonebridge Ranch, Craig Ranch, and Eldorado.

What moves the price: the age of the unit, whether the gate itself is dragging or misaligned, and whether we’re putting in OEM FAAC parts or a quality aftermarket equivalent. We’ll always give you the straight number before we start, and the estimate is free. Call (430) 226-4507 and we’ll come look at it, no charge for the quote.

Why McKinney Homeowners Call Ironworks Gate Co. for FAAC Work

FAAC operators are only as good as the service behind them. We’ve worked on enough of them across McKinney to know that a gate motor isn’t just a box on a post. It’s a system: the hinges carrying the weight, the track the slide runs on, the safety edges, the keypad, and the board making sense of all of it. Our techs are trained on FAAC and eight other automation brands, so when a FAAC board fails and a homeowner asks whether they should switch to LiftMaster or Ghost Controls or Mighty Mule, we can give a straight answer from experience, not a brochure.

We answer the phone 24 hours a day, seven days a week. A McKinney homeowner never gets a voicemail tree when their gate won’t open at 6:40 on a Tuesday morning. And because we’ve been doing this for over 42 years, we plan on being around to honor the 90-Day Done Right Promise on every job we write it on.

FAQs