Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Parts & Welding in McKinney: What to Know First
Independent Ghost Controls gate parts and welding service in McKinney, Texas. We diagnose the failing component, replace it with the correct part, and weld anything structural that has let go, usually in a single visit. Most hardware failures run well under the cost of a new opener, which is why we always look at the hinge, rail, or bracket before we talk about replacing the board. Call (430) 226-4507 and a live person will answer, day or night.
If you own a Ghost Controls opener and the gate is sagging, grinding, or failing to close, you are in the right place. Ironworks Gate Co. is an independent Ghost Controls service provider, not a manufacturer affiliate. We work on Ghost Controls systems across McKinney every week, from historic homes near downtown to the newer acreage properties east of Highway 75. Victor Salinas and our technicians fix the mechanical and structural failures that no board swap will solve.
How Ghost Controls Products Fail - and How We Fix Them
- Gate post fatigue on the TDS2 and TSS1 series. Ghost Controls openers on double swing gates are common in McKinney, and on heavy tube-steel or wood gates, the hinge post takes constant lateral load. We see post lean within three to five years when the post was set in dry-packed concrete instead of a proper footing. The gate operator pushes fine, but the geometry shifts and the opener arm strains. We cut out the lean, re-set or replace the post in structural concrete, and re-weld the hinge plates square before the opener does more damage.
- Bent or cracked operator arms on the R series. The R series arm bracketry is stout, but when a gate drifts out of alignment or a kid swings on it, the arm takes the twist. This is a Ghost Controls failure pattern more than a LiftMaster one, simply because the arm design carries more torsional load. We straighten or weld the arm when sound, and when it is not, we replace it with a quality part that matches the mounting geometry exactly.
- Rail and roller wear on slide gates, including the SL series. A Ghost Controls chain-driven slide gate that grinds as it opens usually has a worn rail or seized rollers, not a motor problem. McKinney’s clay soil expands and contracts enough through the seasons that gate posts and rails shift fractions of an inch, and those fractions chew up rollers quickly. We weld the rail smooth or replace the section, then set fresh rollers and adjust the chain tension so the opener is not fighting the gate.
- Broken hinge welds on custom estate gates. We frequently find factory hinge welds that were never adequate for a 600-pound wood gate. The hinge itself may be fine but the weld at the post or the gate frame lets go. This is a pure welding job: grind out the old weld, re-weld with proper penetration, and often add a gusset plate. Same visit, same day, and the gate swings true again.
- Misaligned photo eyes and limit cams affecting the AXDP and AXD series. When a Ghost Controls gate reverses for no reason or stops mid-travel, homeowners often suspect the board. In McKinney, with our temperature swings, we find limit cam housings that have cracked from heat cycling and photo eyes that have drifted out of alignment on their mounts. We re-secure the sensor bracket, replace a cracked cam, and test full travel with the operator connected before we consider anything electronic.
Our Ghost Controls Gate Parts & Welding Process
- 1
You call (430) 226-4507. A live person answers and asks what the gate is doing. Not a recording, not a callback queue.
- 2
We show up and diagnose. Our technician walks the entire gate: hinges, posts, rail, wheels, arm, opener, safety eyes, board. We find the real cause, not just the symptom.
- 3
We show you the findings and the price. Before any work starts, you get a written number. OEM part, quality aftermarket part, or welded repair, and why. The price is settled before a single bolt is turned.
- 4
We make the repair. We weld what needs welding, replace what needs replacing, and align what needs aligning. On a Ghost Controls system, we replace parts with the correct series match so your existing board, remote, and keypad keep working without reprogramming gymnastics.
- 5
We test it the way you use it. Full open and close cycles, safety reverse, obstruction test, manual release. If it moves when it should not or stops when it should, we will find out why.
- 6
You get the 90-Day Done Right Promise in writing. No paperwork to file. If it is not right, we come back and make it right.
What Ghost Controls Gate Parts & Welding Costs in McKinney
Here is what homeowners in McKinney can expect for common Ghost Controls repairs, and remember that the final price is always quoted and agreed before work begins.
- Hinge replacement, single gate: $180-$350 including labor and standard galvanized or powder-coated hinges.
- Hinge weld repair (no new part needed): $120-$280 depending on access and how much grinding the old weld requires.
- Gate post replacement and re-set in concrete: $400-$900 for a single post, depending on whether we salvage the existing hinge plates or fabricate new ones.
- Rail repair or section replacement on a slide gate: $220-$600, plus roller replacement if needed.
- Operator arm straightening, welding, or replacement: $90-$240.
- Custom welding (cracked frame, gusset plate, fabrication): $95 per hour, one-hour minimum, quoted as a flat rate before we start.
What moves the price: gate weight, whether we can work with the existing metal or need to cut out and replace, access to the post footing, and whether the opener itself has been damaged by weeks of running against a bad hinge. Estimates are free. Call (430) 226-4507 for an exact number before you decide anything.
Why McKinney Homeowners Call Ironworks Gate Co. for Ghost Controls Work
We have been serving McKinney and Collin County for over 42 years, since 1984, back when Eldorado Parkway was still mostly pasture. Victor Salinas grew up off that road and never had much interest in leaving. We are a gate company, not a handyman with a welder. Gate parts and gate welding is what we do all day, every day.
Every job is protected by our 90-Day Done Right Promise in writing, and a live person answers our phone 24 hours a day, seven days a week. Our technicians are background-checked and uniformed, trained to work in your home the way they would work in their own mother’s. And on the rare occasion a Ghost Controls component is not the right fix, we service eight other major brands: LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite. We find the real problem the first time.
FAQs
No. Ghost Controls’ limited warranty covers defects in their opener components under normal use. Mechanical wear items like hinges, rails, and rollers are not covered by a Ghost Controls warranty to begin with, and independent repair of those components does not void opener coverage as long as the repair does not alter the opener itself. As an independent Ghost Controls service provider, we keep our mechanical work and your automation electronics separate and intact.
Both, and we will tell you which we are quoting and why. For electronics, like a control board or receiver, we recommend genuine Ghost Controls parts matched to your series so the programming and remotes stay compatible. For structural steel, brackets, and hardware, we often fabricate or source a quality equivalent that is as strong or stronger, at a better price. You get the final call before anything is ordered or welded.
It is not yet, but it will be. A screech on start-up or through the travel usually means a dry or failing hinge, a worn roller, or a chain running out of tension. Run that way for a few more weeks and the opener motor is doing double the work it was built for. On Ghost Controls openers we see more motor failures from neglected hardware than from anything else. A $89 seasonal tune-up catches this before it becomes a $400 operator replacement. Call (430) 226-4507 and we will listen to the gate over the phone if you want.
Same day is common for hardware failures and welding work, because we carry the steel, hinges, and fasteners on the truck. If your Ghost Controls problem is electronic and we need a series-specific part, we can usually have it the next day and install it on our return. If the gate will not close at all, treat it as urgent: an open driveway in McKinney is an invitation, and we will respond as fast as any gate company in Collin County.
Only if the board or motor has failed and the replacement cost approaches half of a new unit. When the opener itself still runs clean and the problem is a sagging hinge, a cracked weld, or a worn rail, repairing the hardware is the better money. We will tell you straight which side of that line you are on. A square deal means we do not sell you an opener you do not need.
Get Your Ghost Controls Gate Working Right
If your Ghost Controls gate has a bad hinge, a cracked weld, a sagging post, or a rail that is eating rollers, call (430) 226-4507. We serve all of McKinney and the surrounding Collin County communities. Estimates are free, the price is set before we start, and every job is backed by our written 90-Day Done Right Promise. A live person answers, day or night.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving McKinney and nearby areas.